<div dir="ltr">
<p> The first step of making an epoxy clock is mixing two different 
components of Epoxy Resin. When they are mixed properly the resin is 
clear and is able to be easily scraped from the top of your surface. 
Then, warm up the two components in order to make them easier for you to
 use. This causes the resin to melt and to react faster. Once the resin 
has been mixed, carefully put the two pieces on the wooden face of the 
clock. After the resin has hardened then remove the clock face.<br>Step-by-Step Instructions to Create Epoxy Clock<br><br>After
 the resin has completely cure, you are able pouring it into the mold. 
Do not touch the resin you have poured, or allow it to cure. In the 
event that your surface appears too hard, you can use the microbutane 
torch to help soften the surface. It is also essential to keep the mold 
from burning as the heat produced by the torch can trigger the resin to 
bond with the mold. After the resin has completely cured, you can begin 
building the clock.<br><br>Then, you'll have to then paint your Epoxy clock <a href="http://quantumepoxy.co.in">http://quantumepoxy.co.in</a>
 face with the resin. This can be done with small sticks. Use a torch to
 burn off any bubbles that may be popping up. After the resin has cured 
then it's time to take off the mold and tape. Once the clock is painted,
 use a heat gun to eliminate any bubbles that could appear. If you need 
to take a step, make sure you don't touch the surface of the clock, as 
you could damage it.<br><br>When the resin has completely dried, you can
 remove it off of the mold. You could use a microbutane torch to melt 
the resin and pop any bubbles that may form over the top. Then, wait at 
least a few days for the clock to set completely. At the end of 24 hours
 you can begin assembling the clock, and paint the face. After two days,
 you'll be able to finish the fine metals, mica and any other ornamental
 details.<br><br>To finish the clock, you must place the vinyl record on
 an acrylic base. After a couple of minutes, the resin will be cure. To 
remove the mold, you can also use a micro butane torch to warm it 
gently. Make sure to wear gloves as well as a micro butane torch to 
prevent any skin irritation or burns. Within two days you can start 
assembling the clock. After the cure has been completed, you can then 
add the mica powder or precious metals.<br><br>After the resin has dried
 and dried, it is time to remove it from the mold. To achieve this, make
 use of a tiny butane torch to pop up bubbles that may have risen over 
the top of the mold. If the resin is wet, be cautious not to come into 
contact with the plastic as this could cause damage to the clock. After 
that, you can place the acrylic base on the table or place it on the old
 vinyl record.<br><br>Once the resin is cured and dried, it's time 
pouring the mold with the resin. Once the resin is dried, you must make 
sure that it is cool enough to be able to remove the mold. To create a 
perfect, flat clock, use a small butane torch that melts the resin. Be 
cautious not to overheat the resin because it could adhere to the mold. 
After the resin has dried, you should use the foil of gold and various 
other rare metals.<br><br>Then then, pour the resin in the mold and wait
 until the mold has dried. Make sure you don't touch the surface as it 
may cause mess. It is recommended to wear protective gloves when working
 with the material because it isn't skin-friendly. You can make use of 
an ultra-low temperature torch to melt the resin. After that, you can 
cut off the tape. Be cautious not to burn the resin since it might 
remain on the mold made of silicone.<br><br>After preparing the resin , 
and mix the resin and mixing it, pour the resin into the mold and let it
 sit for 10 minutes so that it to cure. It is vital to note that you 
should never be touching the resin while it's still liquid. It can be 
extremely difficult to remove while it is still cured, so be sure to 
adhere to the directions carefully. Then, you need to connect the 
quartz. Following that, you will be able to make use of the quartz 
crystal to set the time.<br><br><br></p>

</div>